The sound of shaving electric push shearing is too loud, what if it is adjusted to a minimum or very loud?
1. If you have a Yuanbao screw on the body of your electric push shearing machine, you can twist it until the sound is reduced. Or you can hold the fuselage of the electric push-shears in your hand and tap gently with a Bakelite hammer. You can also check to see if the knife head is not installed.
2. If the noise is too loud, it is recommended to take apart the knife head to see if the transmission part of the connection between the motor and the tool holder is short of oil. Using Vaseline or lithium grease to lubricate should reduce the sound. Knife head use process is also the need to constantly use special lubricating oil to reduce friction.
3. You can check some of the flippers in time. Screws from all parts. Tighten them properly, and it won't sound like that anymore. Such a big one. I think if you don't check. It might hurt someone. If. When the screws are open to the point. He's going to go bald.
How to repair electric push shears
The maintenance method of Huozhifeng electric push-shear motor is as follows: the electric push-shear scissors are rusty due to lack of lubricating oil and can be lubricated with transformer oil, drop in the electric push and sit for 1 minute. The short circuit of the coil will lead to serious heating of the electric push shear, so it is necessary to replace the coil.
When motor-driven electric push shears make a lot of vibration and noise, it is necessary to check whether the motor is reversed and whether there is looseness between the handle and the rocker arm. Proper adjustment can reduce vibration and noise. (2) if three white paths are found in the hair after electric push and shearing, appropriate adjustments should be made.
Too much noise is recommended to take apart the knife head to see if the connection between the motor and the tool holder is short of oil, using Vaseline or lithium grease to lubricate should be able to reduce the sound, the knife head also needs to constantly use special lubricating oil to reduce friction.
If the noise is high, which means that the blade vibrates violently, the Yuanbao screws and pressing blade screws on the side of the electric push shear should be adjusted appropriately. Points for attention in the use of electric push shears: (1) disconnect the power supply and pay attention to the dripping of lubricating oil between the upper and lower blades when disassembling and installing by yourself.
After poking, continue to turn, that is, the carbon brush is damaged, and the motor can be replaced. If the motor can easily withstand the motor shaft, but the motor is buzzing, the shaft sleeve can be replaced by wear or cracking in the tightening area. 220V also has motors, but there are few, and the repair is the same as charging. It's just that the power supply voltage is high and the motor is large.
... Knife head working sound is very loud, but also blow hair, how to return a responsibility?
1. If the noise is too loud, it is recommended to take apart the knife head to see if the transmission part of the connection between the motor and the tool holder is short of oil. Using Vaseline or lithium grease to lubricate should reduce the sound. Knife head use process is also the need to constantly use special lubricating oil to reduce friction.
2. there are many possibilities. first of all, it may be that your razor has not been cleaned for a long time, and there are too many impurities in it. One of my classmates felt that his voice was a little loud after hearing my Philips voice. It happened that I had just finished flushing it with water. Then he went to clean it up, and then the voice was much lower.
3. There is some hair left inside the barber and on the knife head. Use the small brush that comes with the hair clipper to sweep gently. You can also blow hard, and the effect is very good. Use a syringe to absorb a small amount of lubricating oil, drop a little in the relative movement of the knife head, the amount of lubricating oil can not be large. Drip a little on the motor shaft, too.
4 、 . Whether the knife head is not pushed into place; 2. Whether the screw of the knife head is loose; 3. Whether the clamping bracket of the knife head will collide with the retentive Reed during the movement of the knife head; 4. Whether the shaft of the transmission part is normal or not; 5. If there is no problem with the above, you can see if the transmission shaft is missing a Reed. six.
5. The reason for the sudden increase in sound is often that the knife head is not installed correctly, and the real knife head net can not be shaved together. Look at the two flanks on the knife net and make sure they are fixed when installed on the bracket. in this way, the blade rotating knife net can not turn to shave, and there will be no noise.
How to fix the loud sound of electric push and shears?
Too much noise is recommended to take apart the knife head to see if the connection between the motor and the tool holder is short of oil, using Vaseline or lithium grease to lubricate should be able to reduce the sound, the knife head also needs to constantly use special lubricating oil to reduce friction.
Treatment method: if the noise is high, which means that the blade vibrates violently, the Yuanbao screws and pressing blade screws on the side of the electric push shear should be adjusted appropriately. Points for attention in the use of electric push shears: (1) disconnect the power supply and pay attention to the dripping of lubricating oil between the upper and lower blades when disassembling and installing by yourself.
Reinstall the knife head: put the lower part of the knife head in place first, nudge it and hear a click. It doesn't take much force. Install fixed-length comb: align the chute on both sides and push gently. Remember: contrary to the time of removal, when installing a fixed-length comb, the hairdresser should be adjusted to the shortest "fixed-length" position.
It's just been used for a few days. if you have a Yuanbao screw on the body of your electric push shearing machine, you can twist it until the sound goes down. Or you can hold the fuselage of the electric push-shears in your hand and tap gently with a Bakelite hammer. You can also check to see if the knife head is not installed.
How to repair it
