How to grind the beauty electric push shearing blade
1. First, remove the blade of the electric haircut and push shears and unload it into a blade like the one shown in the following picture. Then clean the hair on the blade with a toothbrush and wear thick gloves to prevent cuts.
2. After the head of the electric push scissors is blunt, the most convenient way is to replace the original blade, you can also grind the blade with oil soaked in oil, you can also take the blade off and adjust the pressure, but it is not easy to grind it on smooth pig iron and then clean it with kerosene.
3. First of all, remove the blade of the electric haircut, as shown in the following picture. Then clean the hair on the blade with a toothbrush and wear thick gloves to prevent cuts, as shown in the following picture.
How to grind the blade of electric hair clipper
Punching, toothing, polishing, electroplating, grinding. There is a special grinding equipment for grinding, not by hand. Put the blade in the tooling, add grinding powder, and start the machine. If the blade is not fast after use, you can find a piece of flat pig iron, add some kerosene, and rub it back and forth a few times.
First, remove the blade from the electric haircut, as shown in the following picture. Then clean the hair on the blade with a toothbrush and wear thick gloves to prevent cuts, as shown in the following picture.
First, remove the blade of the electric haircut and unload it into a blade as shown in the following picture. Then clean the hair on the blade with a toothbrush and wear thick gloves to prevent cuts.
After the head of the electric push scissors is blunt, the most convenient way is to replace the original blade, you can also grind the blade with oil soaked in oil, you can also take the blade off and adjust the pressure, but it is not easy to grind it on smooth pig iron and then clean it with kerosene.
What if the electric push shears can't push the hair?
Lack of power. Charge. The electric push shearing battery will stop automatically when it is fully charged with a protective device, and the battery will not break down after being charged for 24 hours.
When the electric push shear noise is loud or the blade vibrates violently, you can loosen a Yuanbao shaped screw next to the electric push shear and check whether the pressure blade screw is too loose. If it is loose, it should be tightened properly, but not too tight.
Add lubricating oil to the blade. Change the blade. How to use the hair clipper: charging time. Just bought the electric hairdresser, you should pay attention to charge more than 12 hours, which is good for the battery. And if you do not use the barber for more than a month, you should charge the charger for more than 12 hours when you use it again.
Not installed in place; lack of oil; not well protected, rusty-especially the rust between the teeth will hinder the movement of the hair; need to be polished; do not think that the newly bought knife head must be easy to use, and sometimes you will encounter unsharpened ones. For the manufacturer, it is 1/10000. It's inevitable.
The main reasons for hairdressing are as follows: 1 lack of lubricating oil, add lubricating oil to the knife head in time (such as sewing machine oil). 2 too much residual hair of the knife head has not been cleaned, remove the two screws below the knife head and remove the knife head to clean the residual hair.
The blade of electric haircut push shears is disadvantageous, how to grind it?
First, remove the blade of the electric haircut and unload it into a blade as shown in the following picture. Then clean the hair on the blade with a toothbrush and wear thick gloves to prevent cuts.
First, remove the blade from the electric haircut, as shown in the following picture. Then clean the hair on the blade with a toothbrush and wear thick gloves to prevent cuts, as shown in the following picture.
Put on your gloves first. Remove the knife head of the electric push shears. Use a small brush to clean the knife head. Start the grinding plate for grinding the tool head. Put the knife head on the grinding plate and you can grind it.
How can I fix the knife head of the electric push shears if it doesn't turn?
1. Lack of power, charge. The electric push shearing battery will stop automatically when it is fully charged with a protective device, and the battery will not break down after being charged for 24 hours.
2. Add lubricating oil to the blade. Change the blade. The use of electric fader: charging time. Just bought the electric hairdresser, you should pay attention to charge more than 12 hours, which is good for the battery. And if you do not use the barber for more than a month, you should charge the charger for more than 12 hours when you use it again.
3. This is an AC motor type electric push shear. It's heavy. The white one is the drive rod. I don't know if the motor works when you turn it on. If the motor works but the drive rod does not work, it is not installed or a small part is damaged.
4. I think you should see if it is because the wire inside is broken, if there is no normal wire line inside, if there is a problem, then it still cannot carry out a normal activity, and it is a kind of fault.
